More speed, capacity, and endurance. Get more out of your storage.
When the Crucial® MX100 was released, it set a new standard for SSDs that the Crucial MX200 pushes even further. Leveraging leading specs on all fronts, along with new Dynamic Write Acceleration technology, the Crucial MX200 is loaded with innovative features and immediately increases your system’s performance.
How the Crucial MX200 Benefits You
Performance & Endurance
Boot up almost instantly. Load programs in seconds. Accelerate demanding applications with ease.
Do more. Faster. Longer.
The Crucial MX200 delivers 555 MB/s sequential reads on both compressible and incompressible data, and outperforms a typical hard drive by 400 MB/s.1 Even better, the performance doesn’t let up, as the Crucial MX200 posts an endurance rating that’s up to 5 times greater than a typical client SSD.2
Transfer and save large files in a matter of seconds.
Competing SSDs typically rely on a fixed cache of multi-level cell flash memory, which allows you to write sequential data at published specs, but only for so long. Our industry-leading Dynamic Write Acceleration technology solves this problem by using an adaptable pool of high speed, single-level cell flash memory for consistently fast performance that doesn’t let up.
Max out performance and increase reliability.
Our engineers created RAIN technology to protect your data at the component level, similar to how RAID is used with multiple hard drives. This technology increases the security and protection of your data to a level that’s rarely seen in consumer-class SSDs.
Encrypt and protect your data at the highest possible level.
Keep personal files and sensitive information secure from hackers and thieves with AES 256-bit encryption – the same grade used by banks and hospitals. The Crucial MX200 meets or exceeds all industry encryption standards, including Microsoft® eDrive, IEEE-1667, and TCG Opal 2.0.
Efficiency & Reliability
Store up to 1TB of data and achieve a higher level of reliability than a hard drive or competing SSD.
Run your system longer than ever before – using less power.
With Extreme Energy Efficiency technology, the Crucial MX200 is over 2x more energy efficient than a typical hard drive.3
Push your drive to the limit and avoid overheating.
Adaptive Thermal Protection technology enables the Crucial MX200 to dynamically adjust storage component activity based on how you’re using the drive, allowing your storage system to stay cool.
Keep your memories, photos, and files safe.
When a photo or file gets corrupted, it often becomes unusable. Prevent this from happening in the first place with the Crucial MX200, which arms every storage component with four layers of Exclusive Data Defense.
Best-in-class hardware encryption keeps data safe and secure
Sequential reads/writes up to 555 / 500 MB/s on all file types
Random reads/writes up to 100k / 87k IOPS on all file types Up to 5x more endurance and over 2x more energy efficient than a typical client SSD
Dynamic Write Acceleration delivers faster saves and file transfers
Includes spacer for 9.5 mm applications
Internal Solid State Drive (SSD)
NAND flash type
16 nm Micron® MLC
Marvell® 88SS9189 with Micron Custom Firmware
Max Sequential Read
Max Sequential Write
4k Random Read
100 000 IOPS
4k Random Write
87 000 IOPS
Maximum data transfer rate
Mean time between failures (MTBF)
1.5 million hours
TRIM RAIN (Redundant Array of Independent NAND) DWA (Dynamic Write Acceleration) [not required] ATP (Adaptive Thermal Protection) PLP (Power Loss Protection) AGC (Active Garbage Collection) SMART (Self Monitoring and Reporting Technology)
AES 256-bit encrytption TCG Opal 2.0 compliant IEEE-1667 compliant compatible with Microsoft eDrive
7 mm (with 7/9.5 mm spacer)
4 oz / 114 g
The SSD (Solid State Drive)is a storage medium that does not include moving parts. Due to the lack of moving parts, it is not as vulnerable as the traditional HDD, soundless and fast. It can be installed in a Notebook (depending on its thickness) as a PC.
Use real high technology in your car! This is 7.86 inchGPSRearviewMirror with DualCamera (DVR + AV-In + vehicle rear view Camera), WiFi & 3G/4Gmobileinternet support and Android 5.1 Operating System. Blue mirror, unique Ultra Thin design. Precise Capacitive Touch Screen, smooth control. Easy to install android software. Support GPSNavigation, built-in WiFi and 3G/4G, Bluetooth, FM transmitter, MP3/MP4 playing, multiple APP download and etc. It has Android, which has a lot of features like smartphones! Six In One Device with mutiple functions! With built-in GPS receiver you can navigate us anywhere without disturbing the view. With WiFi (802.11b/g/n) capability and 3G / 4G mobile connectivity, it also provides online navigation capability to avoid jams and speeding. With this Android WiFi and 3G/4G Intelligent Rearview Mirror, driving journey will be colorful and joyful. On 7.86 inches 1280 × 480 TFT you can play games, watch videos, clear to see the road and no need to worry about losing your way. With built-in WiFi (802.11 b/g/n) and 3G/4G mobile internet support you can surf in the internet, watch videos, chat with IM, download what you want and update the software online. Mobile Internet can be shared with the built-in WiFi Hotspot for those in the car. By accessing the (WiFi or mobile Internet) Internet via the Internet you can even check your car remotely with your mobile phone (Car Assist) or an alert can be asked for a parking incident. Dual DVRRecorderDash Camera (1080p) and waterproof rear view backup camera with 6 meters cable. PIP function. Screen will automatically switch to rear view when car reversing. Dual front and rear camera can simultaneously record. With TF card slot (max support 64 GB) for DVR and parking record data storage. While you're on vacation you can record with DVR your car trip, and you can record (by the built-in accelerometer) the event of an accident, and use it as decisive evidence in court. In addition to the navigation function, the built-in GPS continuously informs us of our current position and speed and records these data on the recordings. The ADAS (LDWS - Lane Departure Warning System / FCWS - Forward Collision Warning System / FVMA - Forward Vehicle Moving Alarm) support makes driving more secure, ensuring you and your loved ones are in safe reach. The outstanding (FHD) video quality plays a central role in all three functions: it allows the driver to keep track of (and not only) what's driving around your car while driving. As a display, you can display the rearview camera (supplied) and display parking guides can help you adjust. Bluetooth hands-free function allows our mobile phone to be safely handsfree, and we can use it legally in our car while driving. With FMTransmit function, the navigation voice and music will be directly sent to the car speaker. With this function, the sound become better and louder. Thanks to its multimedia capabilities and Internet access, it also functions as a car entertainment center. Multimedia support, play most video, audio format, can do as Android Tablet, e-book, play games, etc. Please connect the car charger after start the car when you use it!
Android 5.1 (Lollipop)
MT6735 (ARMv8 64 bit Quad-core Cortex-A53, 1.3 GHz)
ARM Mali™-T720 MP4 quad-core GPU
1 GB DDR3
16 GB Nand Flash, system will occupy about 3 GB (only for app install and downloading files, but you should put an external TF card if you want to record a video or take photos)
micro SD / TF Card, up to 64 GB for DVR record data storage
Luxury, high quality, anti-glare, blue glass mirror
LDWS (Lane Departure Warning Systems): A warning is triggered when lane departure is detected based on real time video recorded. FCWS (Forward Collision Warning System): A warning is triggered when a possible forward collision is detected based on real time video recorded. FVMA (Forward Vehicle Moving Alarm): An alert is triggered when the vehicle ahead of you moves based on the real time video recorder.
Back flip for motorcycle. Electric motorized license platehideflipper gadget, like ones used in James Bond movies. Install this easy to use retractable license plate gadget and easily hide your license plate at motorcycle meets, shows, events, photoshoots and more. This device is great for use at shows and track events. Fits any motorcycle, scooter or ATV with any size (US, CA, UK, EU, RU, GR, AU, ...) license plate. It is 100% automatic/electric, flip a switch. Installs in no time with just a screwdriver. Comes with everything you need.
switch controlled, switch case can be mounted on handlebar
LED indicator shows the position of the plate
power: 12 V & 36 W (powered by your bikes battery)
materials: hi-strength plastic with black carbon foil and some steel parts
waterproof and weatherproof
tested up to 200 km/h, working even at speed over 200 km/h
winker mount plates
flip angle: 90° degrees
plate is retained in the end positions (shown and hidden) from spring and 2 strong magnets with adjustable retained force
adjustable mounting angle
five mounting options in one product for sport, tour, enduro, cruiser and choppers
mounting plate with many holes and slots for universal fitment
See picture with dimensions to be sure that bracket can be mount on your motorcycle. Modifications may be required (mounting holes drilling or additional auxiliary details).
Realise is high quality real swimsuit from Japan. Normal-back swimming sexy japanese shiny swimsuit / swimwear / hydrasuit / water polo with long sleeves in Realise´s waterpolo cut, with round neck, high leg & covered cheeks (Realise N-Cut), closed back with back zipper. This is a super swimsuit, very shiny and very smooth material. Very similar to the Asics CD in texture but lighter and sexier!
Model: N015 P-2
Normal leg cut
Zip at the back
The material is super shiny when wet
SSW (Super Shiny Wet) a very thin and stretchy material, that is slightly glossy and feels like Lycra, Wetlook and similar fabrics; the light colors are a bit transparent and become more see through when wet
Glossy coating on the top surface and is tight fitting also
Its quite stretchy
There are thin, moderate growth and feeling of clamping (kickback)
Back fastener specification
The concept is completely Japan production, high quality
Powerful and effective, this portablesignaljammer effectively disables any Wi-Fi networks or GPS (L1) and any current mobilephone signals on the 2G (CDMA 850, GSM 900, DCS 1800 and PCS 1900), PHS, 3G (WCDMA 900/2100) and 4G LTE (800/1800/2600 aka 3/7/20) bands without interrupting any other electronic devices. The highly portable size and one-touch power button allows users to quickly turn the device on or off for instant jamming and un-jamming. Incredibly easy to operate and carry around, this portable signal jammer is both the ideal security and anti-security device and quite simply one of the best we have ever tested. This is a powerful palm-sized cellphone signal shield blocker that disables nearly all kinds of cell phone signals, including the 2G (CDMA 850, GSM 900, DCS 1800, PCS 1900), PHS, 3G (WCDMA 850/900/1700/1800/1900/2100) and 4G LTE (800/1700/1800/1900/2100/2600 aka 1/2/3/4/7/20) bands. The device produces a 3 W radio shield with an effective range of up to 20 meters.
Ideal for meeting rooms, restaurants, concert halls, offices, schools – any place where cell phone use is inappropriate or prohibited. The GPS L1 jammer blocked the GPS trackers. Keep students from text messaging and using the mobile broadband internet during tests, and keep unwanted phone calls from disrupting religious services. Usable: private offices, army authorities, police / SWAT authorities, bus and vehicles (imagine how you can finally have a good undisturbed nap), VIP and privacy-sensitive scenarios, etc. Prohibits Wifi Camera & audio, Wifi Network & devices.
Frequencies blocked (independent of the service providers):
2G/CDMA850 (identical CDMA800): 869 ~ 894 MHz (in America)
2G/GSM900: 925 ~ 960 MHz (in the rest of the world)
2G/DCS1800: 1805 ~ 1880 MHz (in the rest of the world)
The GTIL2-LCD GridTiePowerInverter with LCDdisplay is the world’s most technologically advanced inverter for use in utility-interactive applications. This integrated system maximizes energy harvest, increases system reliability, and implifies design, installation and management. You can use this 2nd generation GTIL2-LCD grid tie inverter with Solar Panel [SUN] or Battery [BAT] (DC), Wind turbine [WDL] (DC) and Wind turbine 3 phase [WAL] (AC) input type with configurable 10-30 / 22-60 / 45-90 V input voltage range. The output voltage is pure sine wave auto selected AC 110 / 220 V and 50 / 60 Hz with possible 1000 / 2000 W output power version. Supports it limiter for control the amount of power, dump load controller and resistor for the wind turbine and WiFi plug module for online monitoring. The small type solar and wind grid tie power inverter can obtain the solar energy from solar panel (DC) and wind turbine (DC or AC), and can tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. We call the system combining with small solar grid tie inverter and solar panels as SGPV. The system includes solar panels and small type grid tie inverter and installation kit. Solar panels can be mono silicon, polygon silicon, non-crystal film or any other material that can transform solar energy to electric energy. The power of grid tie inverter should be matched to the power of solar panels connected. So the power of SGPV is defined by its solar panels, it can be standardization according to the actual using. The inverter can be connected to any outlets of utility grid at house. The small grid tie inverter monitors the volume, frequency and phase of the home utility grid, then produce pure sine wave AC power that the frequency and phase are as same as the grid's, and the volume is a bit higher than the grid's, then according to the current controlled PWM, to control the output power to the grid. The small grid tie inverter just puts out power when the home grid is on. When the sun shines, the PV panel will produces DC voltage, and the grid tie inverter will change the DC voltage to AC voltage and puts out power to the home grid. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these power from the inverters will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid. We call the system combining with small grid tie inverter and wind turbine as SGWT. The system includes wind turbine and small grid tie inverter and installation kit, and some SGWT also will include controller, dump load resistor. The inverter can be connected to any outlets of utility grid at house. The small grid tie inverter monitors the volume, frequency and phase of the home utility grid, then produce pure sine wave AC power that the frequency and phase are as same as the grid's, and the volume is a bit higher than the grid's, then according to the current controlled PWM, to control the output power to the grid. The small grid tie inverter just puts out power when the home grid is on. When the wind turbine is rotating, and the output of the voltage is in the range of the rated input voltage of the inverter, the wind turbine will produces power, and the grid tie inverter will change the power from wind turbine to the home grid. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these power from the inverters will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid. When you choose a wind turbine, you also need to consider ahead what model gird tie inverter you want to use. Wind turbines have two output type, one is AC output type, and another is DC output type, if the wind turbine is DC output type, it must be integrated with a rectifier. If the wind turbine is DC output type, then you should choose WDL model inverters, and the input DC voltage range of the inverter should fit the DC output voltage of the wind turbine, the rated power of the inverter should also fit the max power of the wind turbine, and the AC output of the inverter should fit the standard of AC utility grid. If the wind turbine is AC output type, then you should choose WAL model inverters. Most factories don’t supply the AC rated voltage, just supply DC rated voltage, so our WAL also supply the DC input range, please check the DC rated voltage of wind turbine should fit the DC input range of the grid tie inverter.
There are many advantages of SGPV/SGWT compare with the traditional grid tie power system.
Low cost and easy installation - for example SGPV can make full use of all types of buildings’ surface that face to the sun in the city as well as fast and easy installation of solar modules and grid tie inverter. It just needs very low maintenance costs.
Free combination - SGPV or SGWT can be used as a separate grid tie system and can be setup as a large solar or wind array with many of them. The quantity of SGPV and SGWT in the array is just according to your desire. If you are planning to install a grid-tie PV or WT system, in a general way, the solar or wind array and inverter need to be carefully matched to ensure that the inverter’s voltage and power limits are not exceeded. For example when you want to increase more solar panels, and if the total power of the solar panels exceeds the allocation grid inverter, it is necessary to increase the cost of a grid inverter.
Combination of SGPV or SGWT does not interact - The traditional solar and wind grid tie system, they offer units ranging in high power output and these units are modular so you can have multiple units operating in parallel for large solar or wind arrays. For example although, the traditional grid inverter has MPPT feature (Maximum Power Point Tracking), but the maximum power point is according to the entire series in terms of solar panels array, if the performance of a piece of solar panels in the system, for some reason, such as leaves, bird droppings, dust, shadow, etc. and degrades, the performance of the entire solar power system will decrease. But SGPV has no such disadvantage. If the performance of a piece of solar panels in the system degrades, this just effects this piece itself, will not affect other SGPV in the system.
Improving the efficiency of the entire solar or wind power system – For example in traditional grid tie system, the solar panels and wind turbines are connected in series, so the MPPT of the inverter is according to the total panels and turbines in series, not to every panel and turbine, but there is difference between every panel and turbine, so not every panel and turbine is working at the maximum power, this will reduce the total power of these panel and turbine in series. But SGPV or SGWT has no such disadvantage. Because every inverter of SGPV or SGWT has MPPT function, so every panel and turbine is working at the maximum power, this will increase the efficiency of the entire system.
Low power consumption – Most of the parts in the small grid-tie inverter are digital ICs and low power MCU, so the power consumption of it is low, though the quantity of grid tie inverters is increased, but this will not increase the power consumption much of the entire system.
Inverter LCD Display Instruction The Inverter display can show many information, the main interface of the display and the icons explainations are show above. Nice LCD Display showing different parameters vivid and enable varity settings.
Set Menu: Choose the set menu icon on the main screen interface, click the confirm button to enter into the interface show below. In this interface can set the LCD backlight always on or auto turn off backlight after 3 minutes no action. The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. For more details about the limiter function, pls see below. (This function only useful with limiter type inverter.) Battery Discharge Current Mode And Battery Discharge Power Mode see below. (Notes: Save the setting after you reconfigurate the working mode or backlight setting.)
Grid Waveform: This interface will show the real time grid waveform. The grid voltage and frequency also will show in this interface.
Energy Menu: The energy interface will show the power generation curve everyday. Today KWH and Total KWH are also show in this page.
Power View: In this interface the display shows real time power, PV input voltage, inside temperature, date and time.
Clock And Date Setting: Set the clock and date in this page, save the setting before exit.
Simple installation: The Grid Tie inverter converts DC (or maybe AC) power produced by Solar Panels or Wind turbine to AC, connects to the grid and feed all of the power available from the panels to the AC load. All excess power that is not needed by the load is then exported to the Grid. If the Grid fails, then the Grid Tie Inverter will turn off. When the Grid comes back on line. The Grid Tie Inverter will again supply power to the load and any excess power is exported to the Grid again. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid.
The total capacity of the whole grid tie power system is according to your power consumption in the site that you want to install, or how much power that you want it to feed to the utility grid. Actually, the volume is just according to your willingness, because when the total power of electric appliances that are being used in the installation site is larger than the output power of the grid tie power system, these power from the system will be consumed in the site, this will slow down the power meter, otherwise, the difference of the output power from the system between the total used power of the appliances will feed to the utility grid.
Why we produced the GridTieInverter with Limiter?
It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated - because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This problem solved this 2nd generation grid tie inverter with limiter. With the 2nd generation GTIL we integrated the limit function inside the GTI - we call this internal limiter. In this way, no additional limiter module is needed, reduced customer’s cost, more easier for installation. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie - no limit mode, just set on the nice LCD and save your setting. Summary if you do not want to sell electric power, you will need a limiter type inverter.
Using Grid Tie Inverter with Limiter Model: The Grid Tie Inverter with Limiter delivers only the power needed by the load and prevents delivering excess power hence avoids excess power in going back to the Grid. The heart of the Grid Tie Inverter with Limiter is the Limiter Module (LM). The LM continuously sampled the power needed by the load through the current sensor connected after the Main Circuit Breaker. The LM then will process the signal. It then sends signal to Grid Tie Inverter how much power to deliver to the load in real time. The user, after installing and connecting the GTIL correctly, need not do anything and the unit will do its work automatically.
Limiter Setting on the LCD of the inverter: The GTIL include three working mode:
work as normal GTI without power limitation
work under Internal limiter mode
work under External limiter mode
Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. If the distance of meter clam sensor and inverter is too long, you will need the External Limiter. (Note: The external limiter is not included in package.)
Installation of GTIL with Internal Limiter: This installation is not require an additional limiter module, installation is much easier. Clamp the current sensor cable to the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. External protective device including dc and ac SPD (Surge protection device), DC and AC breaker, etc. is recommended to installed in the system.
Limiter Module Specification:
Clamp sensor: max 100 A
Wattmeter: 9999 W
Terminal Block: max 20 A
Receptacle: max 2000 W
Clamp sensor signal: 5 V AC max ?? mA
DC signal Cable: 5 V DC max ?? mA
BatteryDischargePowerMode: New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter, this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged.
WiFi plug module Optional, but can order only together with inverter, connected by RS-232 with RS-485 protocol for Web (https://shinemonitor.com/index_en.html) and Mobile Phone App (https://shinemonitor.com/appDownloadEn.html#iossmartclient) online monitoring.
simple configuration (etc by SmartLink application https://shinemonitor.com/appDownloadEn.html#iossmartlink)
support network with hidden SSID.
Why to choose GTIL2-LCD grid tie inverter?
Advanced patented 2nd generation technology, MPPT efficiency is higher.
High-quality imported components, more stable quality, lower failure rate. Significantly longer life, more than 10 years.
Low cost and easy installation.
Much better output waveform compare with similiar GTI.
Combination of SGPV and SGWT does not interact.
Improving the efficiency of the entire solar or wind power system.
Low power consumption.
Directly connect to three phase wind turbine (WAL).
Build in dump load function (only by wind turbine).
Build in Limiter (internal type).
Attention: Place the Grid Tie Inverter on a surface protected from direct sunlight, high temperatures, and water. The inverter requires at least 150 mm of clearance around itself for ventilation. The inverters are for indoor use, can’t use at outdoor. You can use screws to fix the inverter to the surface, because some models of Sunshine grid tie inverter have fans on the bottom cover, so the surface should be flat.
Circuit Topologies: Half-Bridge Type
Continuous Power Output: 980 / 1950 W
Peak Power Output: 1000 / 2000 W
Input DC Voltage Range: 10 - 30 / 22 - 60 / 45 - 90 V
Max input DC Voltage: 30 / 60 / 90 V
Peak power tracking voltage: 15 - 30 / 25 - 60 / 50 - 90 V
AC Nominal Voltage: 110 / 220 VAC (auto selected)
AC Output Nominal Voltage Range: 90 - 140 / 185 - 265 VAC
Inverter inside temperature: - 20 ~ +75 C (equipment within a wide range of temperature tolerance, to ensure that the equipment can operate normally at higher and lower temperatures)
Dual fan cooling: quickly reduce the internal temperature of the equipment, to ensure the normal operation of equipment.
Stackable: Yes (more than 1 unit inverters can stackable by AC output)
UL1741: be used in distributed power inverters, converters, controllers US standars
IEEE1547: IEEE 1547 standard is applied to micro-grid and grid-connected distributed generation technical standards
VDE4105: germany's new low-voltage grid-connected standards for distributed power generation systems
Certification: CE, ROHS, ISO9001, CCC
Weight: 4 / 6 kg
Dimensions (W x H x D): 322 / 434 x 196 x 88 mm
Options: Input type: Solar Panel [SUN] or Battery [BAT] (DC) Wind turbine [WDL] (DC) Wind turbine 3 phase [WAL] (AC) Input voltage: 10-30 V 22-60 V 45-90 V Output voltage: AC 110/220 V (auto selected) Output power: 1000 / 2000 W
Available options/accessories: (Internal) Limiter function with clamp sensor (opitonal, but can order only together with inverter) Dump load controller and resistor (only order for the Wind turbine) WiFi plug module (optional, but can order only together with inverter)