Green Power

English Deutsch Italian French Español Português 
   
 
 
 
 
 
        Antique, Art
        Car
        Dom
        DVD Movies
        Electronics
        Game
        Green Power
          - Portable
        Hardware
        Health & Beauty
        Hello Kitty
        Household
        Hungaricum
        Interior Design
        Moda
        Navigation (GPS)
        Party Supplies, Decorations
        Phones
        Retro
        Software
        Sport
        Spy & Security Technics
        Tablets
        Travel
        Watch
 
GREEN POWER
 
 Battery Discharge Power Mode / Wind Turbine / Solar Panel (PV) MPPT Grid Tie Inverter with Limiter, LCD Display and WiFi module  Battery Discharge Power Mode / Wind Turbine / Solar Panel (PV) MPPT Grid Tie Inverter with Limiter, LCD Display and WiFi module


The GTIL2-LCD Grid Tie Power Inverter with LCD display is the world’s most technologically advanced inverter for use in utility-interactive applications. This integrated system maximizes energy harvest, increases system reliability, and implifies design, installation and management.
You can use this 2nd generation GTIL2-LCD grid tie inverter with Solar Panel [SUN] or Battery [BAT] (DC), Wind turbine [WDL] (DC) and Wind turbine 3 phase [WAL] (AC) input type with configurable 10-30 / 22-60 / 45-90 V input voltage range. The output voltage is pure sine wave auto selected AC 110 / 220 V and 50 / 60 Hz with possible 1000 / 2000 W output power version. Supports it limiter for control the amount of power, dump load controller and resistor for the wind turbine and WiFi plug module for online monitoring.
The small type solar and wind grid tie power inverter can obtain the solar energy from solar panel (DC) and wind turbine (DC or AC), and can tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable.
We call the system combining with small solar grid tie inverter and solar panels as SGPV. The system includes solar panels and small type grid tie inverter and installation kit. Solar panels can be mono silicon, polygon silicon, non-crystal film or any other material that can transform solar energy to electric energy. The power of grid tie inverter should be matched to the power of solar panels connected. So the power of SGPV is defined by its solar panels, it can be standardization according to the actual using.
The inverter can be connected to any outlets of utility grid at house. The small grid tie inverter monitors the volume, frequency and phase of the home utility grid, then produce pure sine wave AC power that the frequency and phase are as same as the grid's, and the volume is a bit higher than the grid's, then according to the current controlled PWM, to control the output power to the grid. The small grid tie inverter just puts out power when the home grid is on.
When the sun shines, the PV panel will produces DC voltage, and the grid tie  inverter will change the DC voltage to AC voltage and puts out power to the home grid. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these power from the inverters will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid.
We call the system combining with small grid tie inverter and wind turbine as SGWT. The system includes wind turbine and small grid tie inverter and installation kit, and some SGWT also will include controller, dump load resistor.
The inverter can be connected to any outlets of utility grid at house. The small grid tie inverter monitors the volume, frequency and phase of the home utility grid, then produce pure sine wave AC power that the frequency and phase are as same as the grid's, and the volume is a bit higher than the grid's, then according to the current controlled PWM, to control the output power to the grid. The small grid tie inverter just puts out power when the home grid is on.
When the wind turbine is rotating, and the output of the voltage is in the range of the rated input voltage of the inverter, the wind turbine will produces power, and the grid tie inverter will change the power from wind turbine to the home grid. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these power from the inverters will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid.
When you choose a wind turbine, you also need to consider ahead what model gird tie inverter you want to use. Wind turbines have two output type, one is AC output type, and another is DC output type, if the wind turbine is DC output type, it must be integrated with a rectifier.
If the wind turbine is DC output type, then you should choose WDL model inverters, and the input DC voltage range of the inverter should fit the DC output voltage of the wind turbine, the rated power of the inverter should also fit the max power of the wind turbine, and the AC output of the inverter should fit the standard of AC utility grid.
If the wind turbine is AC output type, then you should choose WAL model inverters. Most factories don’t supply the AC rated voltage, just supply DC rated voltage, so our WAL also supply the DC input range, please check the DC rated voltage of wind turbine should fit the DC input range of the grid tie inverter.

There are many advantages of SGPV/SGWT compare with the traditional grid tie power system.
  1. Low cost and easy installation - for example SGPV can make full use of all types of buildings’ surface that face to the sun in the city as well as fast and easy installation of solar modules and grid tie inverter. It just needs very low maintenance costs.
  2. Free combination - SGPV or SGWT can be used as a separate grid tie system and can be setup as a large solar or wind array with many of them. The quantity of SGPV and SGWT in the array is just according to your desire. If you are planning to install a grid-tie PV or WT system, in a general way, the solar or wind array and inverter need to be carefully matched to ensure that the inverter’s voltage and power limits are not exceeded. For example when you want to increase more solar panels, and if the total power of the solar panels exceeds the allocation grid inverter, it is necessary to increase the cost of a grid inverter.
  3. Combination of SGPV or SGWT does not interact - The traditional solar and wind grid tie system, they offer units ranging in high power output and these units are modular so you can have multiple units operating in parallel for large solar or wind arrays. For example although, the traditional grid inverter has MPPT feature (Maximum Power Point Tracking), but the maximum power point is according to the entire series in terms of solar panels array, if the performance of a piece of solar panels in the system, for some reason, such as leaves, bird droppings, dust, shadow, etc. and degrades, the performance of the entire solar power system will decrease.
    But SGPV has no such disadvantage. If the performance of a piece of solar panels in the system degrades, this just effects this piece itself, will not affect other SGPV in the system.
  4. Improving the efficiency of the entire solar or wind power system – For example in traditional grid tie system, the solar panels and wind turbines are connected in series, so the MPPT of the inverter is according to the total panels and turbines in series, not to every panel and turbine, but there is difference between every panel and turbine, so not every panel and turbine is working at the maximum power, this will reduce the total power of these panel and turbine in series.
    But SGPV or SGWT has no such disadvantage. Because every inverter of SGPV or SGWT has MPPT function, so every panel and turbine is working at the maximum power, this will increase the efficiency of the entire system.
  5. Low power consumption – Most of the parts in the small grid-tie inverter are digital ICs and low power MCU, so the power consumption of it is low, though the quantity of grid tie inverters is increased, but this will not increase the power consumption much of the entire system.
Inverter LCD Display Instruction
The Inverter display can show many information, the main interface of the display and the icons explainations are show above. Nice LCD Display showing different parameters vivid and enable varity settings.
  • Set Menu: Choose the set menu icon on the main screen interface, click the confirm button to enter into the interface show below. In this interface can set the LCD backlight always on or auto turn off backlight after 3 minutes no action.Battery Discharge Power Mode / Wind Turbine / Solar Panel (PV) MPPT Grid Tie Inverter with Limiter, LCD Display and WiFi module
    The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. For more details about the limiter function, pls see below. (This function only useful with limiter type inverter.)
    Battery Discharge Current Mode And Battery Discharge Power Mode see below.
    (Notes: Save the setting after you reconfigurate the working mode or backlight setting.)
  • Grid Waveform: This interface will show the real time grid waveform. The grid voltage and frequency also will show in this interface.
  • Energy Menu: The energy interface will show the power generation curve everyday. Today KWH and Total KWH are also show in this page.
  • Power View: In this interface the display shows real time power, PV input voltage, inside temperature, date and time.
  • Clock And Date Setting: Set the clock and date in this page, save the setting before exit.
Simple installation:
The Grid Tie inverter converts DC (or maybe AC) power produced by Solar Panels or Wind turbine to AC, connects to the grid and feed all of the power available from the panels to the AC load.
All excess power that is not needed by the load is then exported to the Grid.
If the Grid fails, then the Grid Tie Inverter will turn off. When the Grid comes back on line. The Grid Tie Inverter will again supply power to the load and any excess power is exported to the Grid again.
If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid.
Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid.

The total capacity of the whole grid tie power system is according to your power consumption in the site that you want to install, or how much power that you want it to feed to the utility grid. Actually, the volume is just according to your willingness, because when the total power of electric appliances that are being used in the installation site is larger than the output power of the grid tie power system, these power from the system will be consumed in the site, this will slow down the power meter, otherwise, the difference of the output power from the system between the total used power of the appliances will feed to the utility grid.

Why we produced the Grid Tie Inverter with Limiter?

It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated - because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This problem solved this 2nd generation grid tie inverter with limiter.
With the 2nd generation GTIL we integrated the limit function inside the GTI - we call this internal limiter. In this way, no additional limiter module is needed, reduced customer’s cost, more easier for installation. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie - no limit mode, just set on the nice LCD and save your setting.
Summary if you do not want to sell electric power, you will need a limiter type inverter.

Using Grid Tie Inverter with Limiter Model:
The Grid Tie Inverter with Limiter delivers only the power needed by the load and prevents delivering excess power hence avoids excess power in going back to the Grid.
The heart of the Grid Tie Inverter with Limiter is the Limiter Module (LM). The LM continuously sampled the power needed by the load through the current sensor connected after the Main Circuit Breaker. The LM then will process the signal. It then sends signal to Grid Tie Inverter how much power to deliver to the load in real time.
The user, after installing and connecting the GTIL correctly, need not do anything and the unit will do its work automatically.

Limiter Setting on the LCD of the inverter:
The GTIL include three working mode:
  • work as normal GTI without power limitation
  • work under Internal limiter mode
  • work under External limiter mode
Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual.
If the distance of meter clam sensor and inverter is too long, you will need the External Limiter. (Note: The external limiter is not included in package.)

Installation of GTIL with Internal Limiter:
This installation is not require an additional limiter module, installation is much easier. Clamp the current sensor cable to the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled.
External protective device including dc and ac SPD (Surge protection device), DC and AC breaker, etc. is recommended to installed in the system.

Limiter Module Specification:
  • Clamp sensor: max 100 A
  • Wattmeter: 9999 W
  • Terminal Block: max 20 A
  • Receptacle: max 2000 W
  • Clamp sensor signal: 5 V AC max ?? mA
  • DC signal Cable: 5 V DC max ?? mA
Battery Discharge Power Mode:
New upgraded firmware enable battery or solar limiter current and power model.
User can set the maximum output power of inverter, this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter.
User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged.

WiFi plug module
Optional, but can order only together with inverter, connected by RS-232 with RS-485 protocol for Web (http://shinemonitor.com/index_en.html) and Mobile Phone App (http://shinemonitor.com/appDownloadEn.html#iossmartclient) online monitoring.
  • simple configuration (etc by SmartLink application http://shinemonitor.com/appDownloadEn.html#iossmartlink)
  • WPA/WPA2 encryption
  • support network with hidden SSID.
Why to choose GTIL2-LCD grid tie inverter?
  • Advanced patented 2nd generation technology, MPPT efficiency is higher.
  • High-quality imported components, more stable quality, lower failure rate. Significantly longer life, more than 10 years.
  • Low cost and easy installation.
  • Much better output waveform compare with similiar GTI.
  • Free combination.
  • Combination of SGPV and SGWT does not interact.
  • Improving the efficiency of the entire solar or wind power system.
  • Low power consumption.
  • Directly connect to three phase wind turbine (WAL).
  • Build in dump load function (only by wind turbine).
  • Build in Limiter (internal type).
Attention: Place the Grid Tie Inverter on a surface protected from direct sunlight, high temperatures, and water. The inverter requires at least 150 mm of clearance around itself for ventilation. The inverters are for indoor use, can’t use at outdoor. You can use screws to fix the inverter to the surface, because some models of Sunshine grid tie inverter have fans on the bottom cover, so the surface should be flat.

Technical Data
  • Circuit Topologies: Half-Bridge Type
  • Continuous Power Output: 980 / 1950 W
  • Peak Power Output: 1000 / 2000 W
  • Input DC Voltage Range: 10 - 30 / 22 - 60 / 45 - 90 V
  • Max input DC Voltage: 30 / 60 / 90 V
  • Peak power tracking voltage: 15 - 30 / 25 - 60 / 50 - 90 V
  • AC Nominal Voltage: 110 / 220 VAC (auto selected)
  • AC Output Nominal Voltage Range: 90 - 140 / 185 - 265 VAC
  • Output Frequency: 50 / 60 (46 ~ 65: 47.5 - 51.5 / 59.3 - 60.5) Hz (auto selected)
  • Output Current: 10 A
  • Standby Power Consumption: < 0.5 W
  • Total Harmonic Distortion (THD): < 5 %
  • Peak Inverter Efficiency: 93.5 % (> 92 %)
  • MPPT Efficiency (PF): 99 % (advanced patented 2nd generetion technology, MPPT efficiency is higher)
  • Power Factor: 0.99Battery Discharge Power Mode / Wind Turbine / Solar Panel (PV) MPPT Grid Tie Inverter with Limiter, LCD Display and WiFi module can stackable
  • Output Wave Form: Pure Sine Wave
  • MPPT Function: Yes
  • Multiple protection to ensure safe use:
    • Over Current Protection: Yes
    • Over Temperature Protection: Yes
    • Short-circuit Protection: Yes
    • Reverse Polarity Protection: Yes
    • Anti-Island Protection: Yes
  • Operating temperature range: -20 ~ +50 C
  • Inverter inside temperature: - 20 ~ +75 C (equipment within a wide range of temperature tolerance, to ensure that the equipment can operate normally at higher and lower temperatures)
  • Dual fan cooling: quickly reduce the internal temperature of the equipment, to ensure the normal operation of equipment.
  • Stackable: Yes (more than 1 unit inverters can stackable by AC output)
  • Product standars:
    • UL1741: be used in distributed power inverters, converters, controllers US standars
    • IEEE1547: IEEE 1547 standard is applied to micro-grid and grid-connected distributed generation technical standards
    • VDE4105: germany's new low-voltage grid-connected standards for distributed power generation systems
  • Certification: CE, ROHS, ISO9001, CCC
  • Weight: 4 / 6 kg
  • Dimensions (W x H x D): 322 / 434 x 196 x 88 mm
Options:
Input type:
Solar Panel [SUN] or Battery [BAT] (DC)
Wind turbine [WDL] (DC)
Wind turbine 3 phase [WAL] (AC)
Input voltage:
10-30 V
22-60 V
45-90 V
Output voltage:
AC 110/220 V (auto selected)
Output power:
1000 / 2000 W

Available options/accessories:
(Internal) Limiter function with clamp sensor (opitonal, but can order only together with inverter)
Dump load controller and resistor (only order for the Wind turbine)
WiFi plug module (optional, but can order only together with inverter)
  498 €  Battery Discharge Power Mode / Wind Turbine / Solar Panel (PV) MPPT Grid Tie Inverter with Limiter, LCD Display and WiFi module   Battery Discharge Power Mode / Wind Turbine / Solar Panel (PV) MPPT Grid Tie Inverter with Limiter, LCD Display and WiFi module
 Small Power Grid Tie Inverter 500 W (15 - 60 VDC input)  Small Power Grid Tie Inverter 500 W (15 - 60 VDC input)


Small Power Grid Tie Inverter 500W (15 - 60 VDC input and 190 - 260 VAC output)

Grid tie inverter is a device which directly converts direct current into alternating current whose sine wave, frequency and phase are the same as power grid and then feed it into utility grid.
It is a key device of power generation systems such as PV power generation system, wind turbine power generation system.It is a key device of power generation systems such as PV power generation system, wind turbine power generation system.
The Grid tie inverter specially optimizes design to work with modularization of DC power supplies which includes the mainstream solar modules, 36V (72 cells) monocrystal.
wind turbines and batteries. Stable, reliable and of high conversion efficiency, it is best choice for PV power generation systems.
The Grid tie inverter can be easily placed and attached to the rack underneath of PV module. It does not need spaces for independent installation and low voltage DC wire connects from the PV module to Smart Microinverter.

Suitable for 30V / 36V solar panels, or 24V / 48V battery grid power generation; Make sure Voc of solar panel is within 24~38V / 44~46V.
Specific design for 24 V (60 cells) and 36 V (72 cells) PV module; but also suitable for 24 / 36 / 48 V battery and small wind turbine system with built-in AC-DC charging controller which’s output voltage is 24 / 36 V.
15 - 60 VDC Wide input voltage, classification processing for different input voltages from different DC power supplies.
Multi-LED indicators, attractive appearance.

Unique circuit design, choice of import industrial electronic components, higher efficiency, more stable performance.
Creative MPPT technology, efficiency more than 99%, faster reaction, more sensitive of reaction and more reliable of Maximum power point locking.
Parallel modular design, small volume, distributed installation, easy for system configuration, flexible for conbination, strong expansibility of system.
Adopting high-frequency isolation transformer type, high efficiency, high security.
Perfect electrical protection function.
Aluminum alloy housing, not rust, heat-resisting and cold-resistant as well as anti-corrosion.
Getting electronic circuit design, appearance design and other core technology patents.

Fetaures:
Input voltage range: 15 - 60 VDC
AC output: 190 - 260 V
Power Output: 500 W
Matched solar panels / Compatible with 36 V (72 cells) solar modules which Vmp is 35-39V and as Voc is 42-46V
Very easy to install (plug and play): Directly connected to the solar panels (do not have to connect the battery)
Pure Sine Wave Output
High-Frequency High Conversion Rate
Power Automatically Locked (APL)
Maximum Power Point Tracking (MPPT): Creative MPPT technology, efficiency more than 99%, faster and more sensitive reaction, more reliable
Automatically Adapt To Different Load Power Factor
Stack Multiple Machines: Multiple small power inverters in parallel by AC output can achieve large output power. In order to achieve higher power use requirements, this  product can be stacked, such as: 5 grid inverter 500W stacking can achieve 2500 W. And the number of the stacking is unlimited.
Aluminum alloy housing, not rust, heat-resisting and cold-resistant as well as anti-corrosion.
Adopting high-frequency isolation transformer type, high efficiency, and high security.
Perfect electrical protection function.
Getting electronic circuit design, appearance design and other core technology patents.
Unique circuit design, choice of import industrial electronic components, higher efficiency, more stable performance.
Constant Current, Constant Power
Islanding protection: When the city power system is in failure, the inverter will automatically turn off the output within 0.5 seconds.
Current Limit Protection
Parallel type design for DC input and modularization design for inverter, small volume, distributed installation, easy for system configuration, flexible for combination, strong expansibility of system.
Weight: 1.15 kg
Dimension: 21X16.5X5.7CM
Dimensions     8.66 in x 6.46 in x 2.13 in (22 cm x 16.4 cm x 5.4 cm)
Weight     46.6 oz (1321 g)

Packing and weight
Net weight  1.3kg
G weight  2.0kg
Size (L x W x H)  21 x 16.5 x5.3cm
Package (L x W x H)  Inner box:34x25x15.5CM     Carton : 51x37x33CM   6PCS/Carton
Installation  Wall hanging
AC power cord length  1.8m
Cooling  Fan

System Function
  Wide voltage input(15-60VDC)
Achievewide voltage input.
1、DC voltage input:15-60VDC
2、Second level powervariable voltageconversion
  High-frequency two-way andone-way grid function
1、  High frequency direct modulation, AC half wave synthesis
2、  Two-way grid means: Load consumedirectly. And can reverse AC currenttransmission.
3、  One-way grid means: Load consume directly. And banned reverse AC current transmission.
  Kinds of frequency output function.
It can applyto 50Hz and 60Hz frequencyof AC.
Frequency range: 45Hz ~ 63Hz
  AC 0 angle with high precision auto-detection
AC phase angle of 0 through isolation amplifierthen input to the MCU for high-precision detection and analysis.
The phase shift rate is less than 1%, thus achieve high-precision with phase modulation AC output together.
1、  ACphase shift: < 1%
2、  Over-zero protection: 0.2 VAC
Synchronous High-frequency Modulation
In the process of the grid, usually adapt the same phase angle in parallel.  (ie, When the two-phase alternating
current  total  is  equal  to  0.Use  switch  to  combination  the  two  AC  fusion)  and  the  product  is  rectified  AC
half-frequency  AC  to  100Hz  first,  then  the  machine  use  the  high  frequency  current  in  the  circuit  and
semi-100Hz frequency alternating current generated combination, to achieve high-frequency modulation.
1、  Modulation synthesis: half wave and full-bridge modulation synthesis (100Hz / 120Hz)
2、  Synthetic way: MOSFET full-bridge
3、  High frequency: 50KHz
Pure Sine Wave Output
Use SPWM directly to make pure sine wave output.
1、Output waveform: Adopt complementary PWM to push-pull pure sine wave.
2、Generate means: enhancement-modeSPWM
  Automatic Sensing Function Solar Luminosity
Use the latest luminosity  perception  operation  technology.  The different illuminate angle and intensity  of  the
solar panel will produce different current output. Use advanced CPU to operate the different illuminance and the
data can be directly displayed on the LCD. Then you can visually see the sense of the strength of the sun unit.
Used more convenient.
1、  Luminositysampling point  :power sampling point
2、  High precision AD sampling: integral AD sampling method
Power Automatically Locked (APL)
In  different current fluctuations, we should  use the MPPT function.  When the MPPT function adjusted to the
maximum  power  point,  the  product  automatically  powers  locked  in  maximum  power  point,  then  made  the
output power more stable.
1、Power lock: The biggest sampling point of MPPT.
Automatically Adapt To Different Load Power Factor
Adapt to any of the power load.
  Constant Current, Constant Power
This product is constant current, constant output power, without any overload, over-current phenomenon.
- 3 -GWV Grid Series
3
  Automatically Shut Down When The Power Output Of a Fault
When the city power system is in failure, the inverter will automatically turn off the output.
Current Limit Protection
Current limit
  Stack Multiple Machines
  Multiple small power inverters in parallel can achieve large output power.
  High-Frequency High Conversion Rate
Adapt high frequency converter, the output more efficient.
  Maximum Power Point Tracking (MPPT)
Current  intensity,  voltage  constantly  changes,  if  there  is  no  power  point  tracking,  then  there  will  be  a  lot  of
problems in the past usually adopted a solar controller, this product uses high-precision MPPT computing power,
automatic  and  immediate  to  solar  panels  output  power  adjustment  in  the  maximum  output  point,  in  order  to
achieve a stable output purposes.
Parameter Table
SY -GWV  Grid-series models  500Watt
Recommend use solar panels  36V/550Wp
DC MAXinput current  50A
AC MAXoutput power  530Watt
DC MAX Open-circuit input-voltage  100VDC
DC input voltage range  15~60VDC
MAX output power factor  >98%
DC input Reverse voltage protection  FUSE
AC output voltage range  120V versions:90~140VAC
AC frequency range  120VAC 60Hz
Output current totalharmonic distortion  THDIAC <3%
AC Phase  <1%
Islanding protection  VAC;f AC
Output short circuit protection  Current- limiting
Show
LED mode:power instruction;voltage instruction;
AC frequency instruction;over-voltage instruction
Standby Power  <1W
NightPower  <1W
Ambient temperature range  -25 ℃~65℃
Humidity  0~99%(no Dew)
Waterproof  Indoor Type Design
Electromagnetic Compatibility  EN50081.part1    EN50082.part1
Power System Disturbance  EN61000-3-2   EN62109
Network test  DIN VDE 1026
Certificate  CE
Fire prevention level(PCB)  94 V0
DC TO AC Conversion efficiency  >85%

Installation Connection
1. Red terminal: Connect DC positive, black terminal: Connect DC negative.
2. AC socket: Connect to the mains. Put the side of the AC cord which has holes into the inverter with 3 foot outlet and the other side of the AC cord to home 3PIN AC outlet.
3. Switch: Connect the connections in right way, then turn on the switch. The inverter starts to work.

Input and output
1、DC input limit
  Input voltage range: 15V to 60V
Solar Panel: Recommend using the power more than 500W and the standard voltage of 36V PV panels.
If use othertypes of solar panels, For example:18V solar panlar:
  Wind turbine system: Rated voltage 24VDC, maximum voltage 60VDC.
  storage battery:  A, 12V*3=36VDC(or 12V*4=48VDC)   Three groups series connection.
B, 24V*2=48VDC(or 24V+12V=36VDC
2、AC output:
  Voltage range of the inverter whose output is 220VAC.: 190V -260V,50Hz&60HZ
  Voltage range of the inverter whose output is 110V AC.: 90V -140V,50Hz&60HZ
5、LED Indicator:
- 7 -GWV Grid Series
7
1、Red LED:
1、Low-voltage protection (input DC voltage is less than 15VDC).
 2、High-voltage protection (InputDC voltage is greater than 60VDC).
3、FAULT: Power grid failure or inverter their own fault.
 4、Power output display: Follow the inverter power output size flow flashing quickly or slowly.
2、Green LED:
1、AC voltage display: Display the power grid voltage.
   125VAC: 90VAC-140VAC
   230VAC: 190VAC-260VAC  
2、AC frequency display: Display the power grid frequency.

Notes
---Non-professionals do not disassemble. Only qualified personnel may repair this product.
---Please  install  inverter  in  the  low  humidity  and  well-ventilated  place to  avoid  the  inverter  over-heating,  and
clear around the inflammable and explosive materials.
---When using this product, avoid children touching, playing, to avoid electric shock.
---Recommended Maximum DC input 4AWG cable capable of handling more than 50A of the
cable size.
---Optimal length of the DC input line 1.8M or less, long cable will allow solar panels to the inverter
DC voltage drop caused by wear and tear.
---Connected to a power outlet to provide AC.
---Connected solar panels, battery or wind generators DC input DC power supply cable.
---Proposed wind power plant with its own charge controller and load dump.

Packing List
1 x Inverter
1 x English user manual
1 x EU plug power cable (150cm)
  183 €  Small Power Grid Tie Inverter 500 W (15 - 60 VDC input)   Small Power Grid Tie Inverter 500 W (15 - 60 VDC input)
Artigos de 1 a 2 (Total 2) Pag.:  1
Locations of visitors to this page
               
Copyright © 2017 The My Shop: Online shop for you!
Call us in USA (1) 360 717 2799 Call us in UK (44) 20 7148 7760 Call us in Italy (39) 069 291 6398 Call us in Spain (34) 851 000 290
Call us in Argentina (54) 11 5239 1330 # 25209 Call us in Brasil (55) 11 3323 1169 # 25209 Call us in Chile (56) 2 595 2806 # 25209
Call us in Guatemala (502) 2 353 3155 # 25209 Call us in Peru (51) 1 705 9745 # 25209 Call us in Panama (507) 202 0400 # 25209
E-mail info@themyshop.eu
Free $5 From Ebates Rebate Site!
Cash Back Rewards & Rebates for Online Shoppers: Ebates! Cash Back Rewards & Rebates for Online Shoppers: Ebates!
Free $5 From Ebates Rebate Site!
Send Free SMS Worldwide